UNRAID SETUP SHARD DRIVE HOW TO
UNRAID SETUP SHARD DRIVE INSTALL
UNRAID SETUP SHARD DRIVE FULL
UNRAID SETUP SHARD DRIVE CODE
UNRAID SETUP SHARD DRIVE PC

To open the network configuration file with mcedit, at the prompt type Then remove the flash drive and open the network configuration file on another computer using Notepad or another text editor you are familiar with.

UNRAID SETUP SHARD DRIVE FULL

If you type this on an array with a configured parity drive it will force a full parity calculation when you reboot. Note: the 'shutdown -h' command DOES NOT cleanly stop the array. To do that, shutdown the UnRAID server by typing

UNRAID SETUP SHARD DRIVE PC

If you wish, the editing can be done on your windows PC instead. By default, the only two text editors installed with UnRAID are 'vi' and 'mcedit.' If you are not already familiar with 'vi' it is suggested you use 'mcedit' as it is much easier for a beginner. If you do not have a DHCP server on your network, you must manually set an IP address for your UnRAID server. Note your IP address now, you may need it shortly, and skip to the next section, or continue to the next section to set a static IP address. If you do not have a DHCP server you need to set your network settings manually. If there is nothing after inet addr make sure your network cable is connected, and you have a router or other DHCP server on your network. The IP address (numbers) after inet addr will almost certainly be different, but anything that has .x or 10.x.x.x means your UnRAID server received an IP address from a DHCP server and is connected to the network and is ready to go. This will present quite a bit of information, however, the only line we are interested in is the one containing To verify that your UnRAID system is connected to the network, at the prompt type enter The prompt should change is hereafter referred to as the prompt. Type root and press enter to log into the system. When the system has been booted you will be greeted with a prompt similar to Now that you have the required files on your flash drive, use it to boot your UnRAID system.

UNRAID SETUP SHARD DRIVE CODE

Step 2 Download the unmenu_install script from the Google Code website and unzip the file on your PC.Ĭreate a folder named unmenu in the root of your flash drive.Ĭopy unmenu_install to the unmenu folder on your flash drive. Unzip the file and copy preclear_disk.sh to the root of your flash drive.

You must be logged into the forum to see the file.

The download is at the bottom of the first post.

Step 1 From a non unRAID system download the preclear_disk.sh script from this forum post.

UNRAID SETUP SHARD DRIVE INSTALL

The preclear_disk.sh script will enable you to prep your disks for the array and the unmenu_install script will install UnMENU. Installing UnMENU will also allow configuration of the environment toĪllow the preclear script to send email notifications of its status.īefore booting your unRAID system you need to copy a few files to your flash drive. You run commands directly from the console, skipping UnMENU and Screen You do not mind keeping a telnet session open for potentially days or You to start a process (such as a preclear) in a telnet session, thenĭisconnect the telnet session and allow the process to continue. The unmenu_install script is used to install UnMENU which The merits of preclearing are discussed in this Script is used to test your disks and prepare them for the unRAIDĮnvironment. Pre Boot Note: If you are in a hurry you may skip copying the preclear_disk.shĪnd the unmenu_install scripts to your flash drive. If you are unclear about any of those, read the linked articles/guides, perform your own research, and ask questions in the Forums. You don't need to be a network administrator, but if you don't know what an IP address is you should spend some time on google!

You have a basic understanding of computer networking concepts.

UNRAID SETUP SHARD DRIVE HOW TO

You know what a command prompt is and how to access it.

You are familiar with (or will become familiar with) using terminal sessions with SSH or Telnet or the server console.

If you have not, please see the Official installation guide and do so now.

You have 'installed' unRAID to your flash drive.

Note: These instructions assume the use of a Windows computer,īut if you don't have access to one, the instructions areīasically the same for Linux or Unix-based operating systems. This guide is intended to get you from a completed and working flash drive to a usable array.

11.2 Copying Files From an Internal or External Hard Drive.

9.1 Adding a Parity Drive to an Existing Array.

8.1 Preclearing via Web GUI with unRAID v6.

5.3 Configure SMTP Settings (unRaid v6).

5 Install UnMENU for Screen and Email Notifications.

4 Configuration With the Server Management Utility.

3.3 Verifying SATA Hard Drives are Detected.

Unraid setup shard drive